膠體系列
Nominal Voltage: 12V 2V
Design Life: 10-12 years
Capacity: from 31AH to 3000AH
Applications: Emergency lighting system Electric tool Geodesic apparatus. Fire alarm Safety Alarm, UPS system. Control system，Medical treatment equipment. Back-up power system. Portable power. Power system, Railway system. Ship quipment, Military，equipment, Telephone switching system than 350 cycles on 80 deep discharge, long life and low self-discharge, high recovery capability on deep discharge.
Characteristic: Special lead-calcium alloy plate and high purity additive ensure more than 350 cycles on 80 deep discharge long life and low self-discharge. high recovery capability on deep discharge.
電壓：12V2V
設計壽命：10－12年
容量：31AH－3000AH
應用范圖：應急原明；電動工具；電動玩具；測量位器；消防報管；安全昏報；UPS系統；控割系；區行被：備用電力能源；計算機備用電源；電力系統；鐵路系統；發電站；船船設備；設備及電話交換機等
性能特點：采用特殊的正極板福鉛合金以及特的鉛音配方和添加劑，使電池80％限度放電循環壽會達到350次以上。壽命長，衰減慢，放電恢復性能良好。
性能特點
Characteeristics
1、閥控式鉛酸蓄電池免維護，循環壽命長。
Valve Regulated Lead Acid (VRLA) Battery, Maintenance Free (no topping up)
2、采用率的超細玻璃纖維（AGM)隔板，氣體符合效率達到98％
Absorbent Glass Mat(AGM)Separators technology for high efficiency, gas absorption of up to 98%
3、特殊的高錫合金板柵材料，降低了板柵的腐蝕效率，延長電池使用壽命了電池的壽命。
Advanced lead tin calcium alloy, reduces grid corrosion & promotes long battery life
4、失水極少無電解液層化現象。
Little water losing, no electrolyte stratification phenomenon
5、充放電能力強。
Performance excels at high rates of discharge & recharge
6、開閉閥靈敏，阻止外部空氣侵入，釋放多余氣體保障安全，保持一定的范圍的氣壓促進氣體復合。
Vent Valve -allows the release of excess gases & prevents case rupture
7、良好的深放電恢復性能。
Good deep discharge resilience performance
8、安全性能好，正常使用下電解液不漏出，無電池膨脹破裂。
Excellent safety performance: No electrolyte leakage, battery swelling and cracking under correct operation
9、熱容量大，減少了熱失控的風險，不易干涸，可在較惡劣的環境中使用。
High thermal capacity, reduce the risk of thermal out of control and drying hard, can be used in bad environment
10、耐大電流性能好：完全充電狀態的電池2CA放電分鐘或10CA放電5分鐘。無導電部分熔斷，無外觀變形
Good resistance to high current: The fully charged batter is proved to be withoutconductive part netted or any appearance deformation after discharge at 2CA for 5 minutes or 10CA for 5 seconds
11、嚴格遵照IEC 60896－2ir22，JISC 8704－2，GB／T19638 2等標準。
Design according with IEC 60896-21/22: 2004. JS C 8704-2, GB/T 19638.2, etc

查看全部介紹